Mit dem Smart Reporter habe ich folgende Werte erhalten:
/private/var/folders/82/mq8czmtj4s325270p2jz5fym0000gn/T/AppTranslocation/C35C191B-3D85-43ED-A727-A0418E94D785/d/SMARTReporter-DEMO.app/Contents/Resources/smartctl --tolerance=permissive --drivedb=/private/var/folders/82/mq8czmtj4s325270p2jz5fym0000gn/T/AppTranslocation/C35C191B-3D85-43ED-A727-A0418E94D785/d/SMARTReporter-DEMO.app/Contents/Resources/drivedb.h --smart=on -a disk0
smartctl 6.5 2016-05-07 r4318 [Darwin 16.4.0 x86_64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: APPLE HDD TOSHIBA MK5065GSXF
Serial Number: X2MRC2C3T
LU WWN Device Id: 5 000039 454006f5c
Firmware Version: GV201B
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Feb 25 16:42:14 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 169) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 2089
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 7847
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 110
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 086 086 000 Old_age Always - 5728
10 Spin_Retry_Count 0x0033 253 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 4569
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 21003
192 Power-Off_Retract_Count 0x0032 094 094 000 Old_age Always - 3328
193 Load_Cycle_Count 0x0032 059 059 000 Old_age Always - 413025
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 36 (Min/Max 12/46)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 53
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 73
222 Loaded_Hours 0x0032 088 088 000 Old_age Always - 4801
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 314
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 1581
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Sind das die benötigten Werte?