ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000e 114 099 006 Old_age Always - 64446166
3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 091 091 020 Old_age Always - 10201
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 089 060 030 Pre-fail Always - 821812507
9 Power_On_Hours 0x0032 073 073 000 Old_age Always - 24424
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 091 091 020 Old_age Always - 10155
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 090 090 000 Old_age Always - 10
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 12
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 059 056 045 Old_age Always - 41 (Min/Max 31/41)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 468
192 Power-Off_Retract_Count 0x0032 093 093 000 Old_age Always - 15941
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 838522
194 Temperature_Celsius 0x0022 041 044 000 Old_age Always - 41 (243 52 0 0 0)
195 Hardware_ECC_Recovered 0x001a 051 045 000 Old_age Always - 64446166
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 001 001 000 Old_age Always - 8206
SMART Error Log Version: 1
ATA Error Count: 5
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 5 occurred at disk power-on lifetime: 15366 hours (640 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 9a bd dc 0f Error: UNC at LBA = 0x0fdcbd9a = 266124698
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 18 b8 dc 4f 00 00:00:48.572 READ DMA EXT
25 00 00 18 b8 dc 4f 00 00:00:46.360 READ DMA EXT
25 00 00 18 b8 dc 4f 00 00:00:44.060 READ DMA EXT
25 00 00 18 b8 dc 4f 00 00:00:41.848 READ DMA EXT
2f 00 01 10 00 00 00 00 00:00:41.848 READ LOG EXT
Error 4 occurred at disk power-on lifetime: 15366 hours (640 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 9a bd dc 0f Error: UNC at LBA = 0x0fdcbd9a = 266124698
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 18 b8 dc 4f 00 00:00:41.848 READ DMA EXT
2f 00 01 10 00 00 00 00 00:00:41.848 READ LOG EXT
60 00 00 18 b8 dc 4f 00 00:00:39.643 READ FPDMA QUEUED
60 00 30 ff ff ff 4f 00 00:00:39.611 READ FPDMA QUEUED
60 00 40 ff ff ff 4f 00 00:00:39.608 READ FPDMA QUEUED
Error 3 occurred at disk power-on lifetime: 15366 hours (640 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 9a bd dc 0f Error: UNC at LBA = 0x0fdcbd9a = 266124698
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 18 b8 dc 4f 00 00:00:39.643 READ FPDMA QUEUED
60 00 30 ff ff ff 4f 00 00:00:39.611 READ FPDMA QUEUED
60 00 40 ff ff ff 4f 00 00:00:39.608 READ FPDMA QUEUED
60 00 20 ff ff ff 4f 00 00:00:39.607 READ FPDMA QUEUED
60 00 10 ff ff ff 4f 00 00:00:39.607 READ FPDMA QUEUED
Error 2 occurred at disk power-on lifetime: 15366 hours (640 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 9a bd dc 0f Error: UNC at LBA = 0x0fdcbd9a = 266124698
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 18 b8 dc 4f 00 00:00:33.009 READ DMA EXT
25 00 00 18 b8 dc 4f 00 00:00:30.548 READ DMA EXT
ef 10 03 00 00 00 00 00 00:00:30.498 SET FEATURES [Enable SATA feature]
ef 02 00 00 00 00 00 00 00:00:30.497 SET FEATURES [Enable write cache]
ef aa 00 00 00 00 00 00 00:00:30.497 SET FEATURES [Enable read look-ahead]
Error 1 occurred at disk power-on lifetime: 15366 hours (640 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 9a bd dc 0f Error: UNC at LBA = 0x0fdcbd9a = 266124698
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 18 b8 dc 4f 00 00:00:30.548 READ DMA EXT
ef 10 03 00 00 00 00 00 00:00:30.498 SET FEATURES [Enable SATA feature]
ef 02 00 00 00 00 00 00 00:00:30.497 SET FEATURES [Enable write cache]
ef aa 00 00 00 00 00 00 00:00:30.497 SET FEATURES [Enable read look-ahead]
ef 03 46 00 00 00 00 00 00:00:30.497 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.