Windows XP läuft auf einem iMac...

Bei der WinXP Installation kommt aber kein V-out Signal.
 
Hier die Kurzanleitung (ist auch eine laengere dabei wo jeder Schritt genau beschrieben wird, sogar wie man eine Datei entpackt :)):
I. Preparing the XP installation disc.
======================================

A custom slipstreamed CD is required to install XP on a Mac.

What you'll need
----------------
1. An original XP PRO SP2 CDROM
It doesn't have to be bootable, but it should have a I386
directory on the root.
2. The xom.zip file.
3. Nero Burning ROM
4. A blank CD
5. A PC of course...
6. 20-30 minutes

Quick instructions for those knowing what they're doing
-------------------------------------------------------
1. Unzip the xom.zip file
2. Use the included sp2.nrb nero project as a baseline.
3. Add the XP source files to the root of the project
4. Overlay the XOM files (in the patch folder) to the root.
5. Set the boot loading image to the included boot.img.
6. Burn and done.

II. The installation
====================

The iMac needs to be repartitioned in order to do this.
This procedure requires reformatting the HD. I have not tried
partition managers but if you're feeling adventurous you may
try one. I do not guarantee results in those cases, though.

Be forewarned: This procedure WILL WIPE YOUR iMAC DISK CLEAN.
Backup any files you don't want to lose.

What you'll need
----------------
1. An intel iMac (iiMac henceforth)
2. The XP CD prepared above.

Quick instructions for those knowing what they're doing
-------------------------------------------------------
1. Partition the disk in two using the OSX CD: FAT and HFS+
2. Install OSX on the HFS+ partition.
3. Copy xom.efi (from xom.zip) into the hard disk
4. cd to the directory where you put xom.efi and type
sudo bless --folder . --file xom.efi --setBoot
5. Reboot, insert the XP CD, select windows using the arrows
and wait about 3 minutes
6. Choose the FAT partition you previously created.
(choose, not create! it should prompt for filesystem)
7. Install. Make sure to remove the CD on subsequent boots,
otherwise you'll start the process over again.
Note: The "press any key to boot from CD" prompt doesn't work yet
8. Done!

Die Seite mit dem Download ist wohl gerade down (http://windowsxp.onmac.net/). Wenn jemand den Patch unbedingt gleich haben moechte, kann er mir gern eine PN schicken.
 
deus-ex schrieb:
Aber wenn ich WinXP auf´m Mac habe und dort nicht die komplette Hardware nutzen kann (allein schon Lan und Wlan) dann bringt das nicht viel finde ich.
LAN: standardmäßiges Marvell-Gigabit-LAN.
Ich hab's nicht ausprobiert, aber ich behaupte mal, dass das wirklich kein Problem ist.
WLAN ist Broadcom, das gibt's auch Windows. Wenn Apple da wirklich was eigenes zurechtgeschustert hat, dann kann man es immer noch per USB nachrüsten, wenn man's wirklich braucht.

Und Virtual PC wird auch irgendwann kommen...
 
Qoco schrieb:
Hier die Kurzanleitung (ist auch eine laengere dabei wo jeder Schritt genau beschrieben wird, sogar wie man eine Datei entpackt :)):


Die Seite mit dem Download ist wohl gerade down (http://windowsxp.onmac.net/). Wenn jemand den Patch unbedingt gleich haben moechte, kann er mir gern eine PN schicken.
Habs auch hier, leite auch gerne per Mail weiter. Sind knapp 800kB.

Gruß
Toowok
 
hat es denn aus diesem Forum nun schon jemand getestet ?
wenn ja, berichte!!
vor Allem mit MBP ;)
 
Ich will, aber kann nicht, da man zum brennen der Windows CD Nero benötigt :(
und der läuft nur auf einem PC, den man erst einmal haben muss...

Irgendwie hat der nicht daran gedacht, dass einige Windows auf einem Mac installieren wollen weil sie keinen PC mit Windows haben, wie sollen wir dann die CD mit nero brennen??

naja, mal abwarten...
 
Zuletzt bearbeitet:
Zurück
Oben Unten